Skip to main content
RealCostIQ

2026 state estimate · 6 metro areas · updated 2026-07-22

How much does it cost to replace an HVAC system in Texas?

Averaged across the 6 Texas metro areas with published BLS wage data, a typical hvac / ac replacement runs $7,564 — about 4% below the national average. Across the state the range is $3,436 to $11,945, and Austin runs about 9% more than El Paso.

Low

$3,436

Basic job, El Paso labor rates

Typical

$7,564

Statewide average of 6 metros

High

$11,945

Complex job, Austin labor rates

What's priced: Full system replacement — condenser, air handler and coil — for a typical single-family home, installed on existing ductwork. Excludes permits, structural repairs found mid-job, and premium upgrades. National typical for comparison: $7,875.

Texas metro areas, priciest first

The state figure above is the unweighted average of these 6 rows. If your project is in one of them, that metro's page is the more accurate number — this one is for comparing Texas against the country, not against your own ZIP.

Metro area (BLS definition)TypicalRangeLabor factor
Austin, TXAustin-Round Rock-San Marcos, TX$7,839$3,733–$11,945×0.987
Dallas, TXDallas-Fort Worth-Arlington, TX$7,745$3,688–$11,803×0.953
Houston, TXHouston-Pasadena-The Woodlands, TX$7,688$3,661–$11,714×0.932
San Antonio, TXSan Antonio-New Braunfels, TX$7,635$3,636–$11,635×0.913
McAllen, TXMcAllen-Edinburg-Mission, TX$7,263$3,459–$11,068×0.778
El Paso, TXEl Paso, TX$7,216$3,436–$10,996×0.761

Why a single Texas number is the wrong number

HVAC / AC replacement prices move with local trade wages, and those do not stop at a state line. Inside Texas the spread between El Paso ($7,216) and Austin ($7,839) is about 9% — often larger than the gap between Texas and the national average, which is 4%. Use the state figure to set expectations, and the metro row above to budget.

The averaging is also deliberately plain: every metro counts once, regardless of how many homes are in it. That over-weights the smaller metros — we have no population or permit-volume series we can defend weighting with, so we say what the number is rather than dressing an invented weighting up as precision.

Get a number for your own job

State averages cannot see your size, materials or access. Run your own specification through the calculator, then apply the labor factor from your metro's row above to the labor portion of the result.

Open the hvac / ac replacement calculator →

How we calculate this

This page adds nothing to the model behind the metro pages it links to. We take a national installed-cost range, split it into labor and materials, scale only the labor half by each metro's actual wage data, then average the metro results. No new cost basis, no new source, and no figure here that a metro page would disagree with.

  • National range: $3,750–$12,000, from our hvac / ac replacement cost data (last verified 2026-07-13).
  • Labor share: 35%. An industry rule of thumb, not a measured value — the softest assumption here, which is why we state it rather than bury it. HVAC is equipment-dominated: the condenser, air handler, and coil are a majority of the cost and are priced nationally. That compresses the metro spread relative to roofing — local labor still matters, but it is moving a smaller share of the total.
  • Metro labor factor: the mean annual wage for hvac mechanics and installers in each metro area, divided by the national mean for the same occupation.
  • State figure: the unweighted mean of the 6 metro typicals above. The low and high are the lowest and highest figures any Texas metro produces, not a separate calculation.
  • Which metros count as Texas: every metro area whose BLS definition includes part of the state, which is why the table prints the full MSA name on each row. A metro area that crosses a state line is counted for both states, and only the counties inside Texas are actually in Texas — read the MSA name before assuming statewide coverage.
  • Materials: held at the national level. We vary labor by metro and hold materials at the national level. That is deliberate: shingles, copper, HVAC equipment, and cabinets are nationally traded and priced, and what actually varies locally is freight and sales tax — both small next to the labor spread. We have no metro-level materials index we can defend, so rather than invent one, we vary only what we can source.
  • Coverage rule: where BLS suppresses wage data for a metro we publish nothing for it, and a state with fewer than 2 covered metros gets no state page at all — one metro is not a state average.

Wage source: U.S. Bureau of Labor Statistics — Occupational Employment and Wage Statistics (OEWS), metropolitan area estimates, May 2025. A U.S. Government work, in the public domain and free to reuse.

Educational estimate only. A real quote for your specific property beats any model, including ours — get at least three.

Related